Valve Publishes Steam Frame CAD and Port Specs

Valve has put the Steam Frame’s HARDWARE references in PUBLIC view: stripped-down CAD for the core module, head strap and controllers, plus a 14-page ELECTRICAL spec for the headset’s nose-bridge expansion port. The fine print is the STORY. The port can feed an accessory up to 2A at 3.1V, and Valve’s OWN document WARNS that the ALLOWABLE 6W draw “will consume over 25% of the available battery capacity.”

Road to VR flagged the release on OCTOBER 12 alongside its write-up of the SteamOS 0.4 update. The files themselves sit in Valve’s SteamHardware/SteamFrame repository on GitLab, described as “Public Steam Frame CAD and Electrical References.” The repository’s single commit is dated OCTOBER 2, and the file names carry dates from September 17 (core module) to October 1 (the port spec).

What Is Actually in the Repo

  • Expansion-port documents, including the spec PDF and front and back DXF outlines for a mating PCB.
  • STRIPPED-DOWN CAD of the CORE module and the head strap.
  • CONTROLLER CAD and a PDF of the controller LED LOCATIONS.
  • A FULL USB 3.0 hub reference design built in Altium, split into a breakout board, a flex cable and a PCIe-to-USB board using Renesas’ UPD720202 controller.
  • A MINIMAL USB 3.0 example in KiCad, which Valve says it does NOT recommend for a real accessory because of its rigid connection to the port.

One PCIe Lane, Borrowed From a Camera

The 44-PIN port is MAINLY a CAMERA interface: two four-lane MIPI D-PHY links at up to 2.5 Gbps per lane. To get PCIe, the headset multiplexes the LEFT camera’s signals into a SINGLE PCIe Gen4 LANE, so an accessory can run one camera plus PCIe, or PCIe ALONE. Valve lists 1 D-PHY camera with 1-lane PCIe Gen4 as SUPPORTED. Two C-PHY cameras are “likely” possible but NEVER tested and UNSUPPORTED.

The port is also LOCKED down by default. Power stays OFF until the accessory grounds pin 44, and the headset then REMOVES it again unless one of THREE probes succeeds: a recognized camera configuration (the document names the Arcturus RGB camera), the strobe and reset pins SHORTED together for power-only or PCIe-only devices, or a valid reply from an EEPROM or temperature sensor on the I2C bus. Anything needing CUSTOM configuration or driver work is expected to carry an EEPROM similar to a CAT24C32. All digital I/O is 1.8V, and Valve warns the PCIe reset, wake and clock-request lines are NOT 3.3V tolerant.

That Arcturus reference matters because the port already has a SHIPPING use. We covered Road to VR’s take on the Arcturus Vision camera as a fix for readable passthrough on the Frame.

The Power Caveat, and a Running Change

The 3.1V rail is rated for 2A CONTINUOUS with a current LIMIT near 3A. The spec also discloses that EARLY devices used a part rated for ONLY 1A continuous, and that Valve made a “running change” to the 2A part at ramp. The document does NOT say how to tell which part a given headset has, or which serial numbers are affected. BUILDERS aiming at the full 2A budget should treat that as an OPEN question.

The battery warning lands on a headset where RUNTIME is already the sore point. Road to VR’s review put mixed use at roughly 1 to 1.5 HOURS before SteamOS 0.4 claimed efficiency gains of up to 12%. A 6W accessory would eat MORE than that gain on its own. Our earlier SteamOS 0.4 coverage has the rest of that update.

Hobbyists Only, for Now

The materials are licensed under Creative Commons BY-NC-SA 4.0. That means attribution, share-alike and NO commercial use. Valve asks would-be SELLERS to contact it about a COMMERCIAL license, and its license text says opening the enclosure, or attaching hardware that is not “Steam Frame Compatible” to the electrical ports, will VOID the warranty. Valve also reserves the right to change the hardware design “in any way.”

The takeaway: Valve has published enough DETAIL to build a REAL PCIe or camera accessory, and has been unusually CANDID about the LIMITS. The open items are a commercial path that Valve has not PRICED or described, and a 1A-versus-2A supply question that owners CANNOT yet check from the documents alone.

Sources: Valve, Steam Frame hardware reference repository; Road to VR, October 12, 2026; Valve, SteamOS 0.4 for Steam Frame.

Leave a Comment